Wire Wrapping Irregular Stones

Step 4: Bending & Shaping. Using your pliers make a bend in the middle of your wire-wrapping using your perfectly imperfect stone as a reference. Bend your wire around your stone (Remember wonkiness is character!) Decide how tall you want your pendant to be and "dent" the wire (Pic. 3) at your chosen length. How to Wire Wrap an Irregular Shaped Stone "Create with Me" TutorialIn this video you will learn how to create a wire woven cabochon using an irregular shape.

Simple weave, step by step tutorial with a few swirls to show you how brass wire handles. I hope you are inspired. Or maybe just drool over the citrine! Eith. Basic Net Wire Wrap: This is a good rustic wrap for irregular stones, crystals, and sea glass. To dress it up a little you can use longer wires and add beads or charms as you close the bail at the end.. Tuck the end of the wrapping wire under the one sticking down and trim it. Step 8: Adding Spirals.

Choose either the topmost or bottom-most wire of your combined bundle and wrap all wires together in a binding that tightly twines the top of your design together. A few wraps of 22-gauge square hard wire at the top should do. Once you have finished this binding, you may remove the tape. 2.

Step 2: Bend the wire to 90 degrees halfway through the pebble's length. Wrap the bent part all around the pebbles' width and bring the wire back to the looped wire part. Now, we will wrap the wire around the pebble upwards. Start the wire wrapping from below the 90-degree bent part but keep adjacent to the bent part, not too far away.

10. Remove the stone and cross your wires over each other as pictured. The left two should be inside the right two (or vice versa). 11. Place your stone back inside the wire wrap, so that two wires are in front and two in back (one each from the right and left). It won't stay in place on its own at this point.

5. Wire Wrapping Stones by Make And Fable. Netting is a method that creates a netted effect and is really great for crystal points, but also works well on smooth, tumbled stones and sea glass. This is slightly more complex technique, that creates a netted effect that looks like a fisherman's net or chain link fence.

Step 1 - Cut Framing Wires. The beginning of some wire wrapped pieces! Cut three or four wires for your stone, they should be 4-6" longer than you need to wrap around the stone. This doesn't need to be exact by any means, but more is better if you're not working with a metal like silver or gold.

Stack your base wires together and start wrapping around all wires. At this point, you can use any wire weaving pattern that is suitable for 3 base wires. For the purpose of this wire-wrapping tutorial, I'm keeping it simple. Wrap around base wires about 14-15 times (approx. 1/4″) and finish off by wrapping around top base wire. (fig. 2a, 2b)

Thanks Camilla for the inspiration! The irregular shape of this tiger eye makes it difficult to wrap with the normal cab wrap. That's what I did initially and I failed miserably. With 3 wires, I formed the frame, holding the stone in place securely. Wrapped them with 3 different weaving techniques as you can see from the pictures here.

Step #3. Twist and twist it until you get at least 6 or 7 turns and then with the pliers you sink the center a little bit, here you will get the base of your stone's fastener. Step #4. Place the stone inside the snail and start wrapping the remaining wire around it. Try to leave space between the wraps so that the stone can be seen (if you.

My first attempt at video editing.This wire wrapping tutorial can be used on stones of almost any shape. It is my favourite go to wrap for odd shaped stones..

7.Slide your gemstone in the spiral and bring the two halves together, caging the stone inside. No stone will be as round as the cage, so use your fingers to manipulate the wire to fit the stone and arrange the coils evenly. 8.Make a loop at one end of the cage by using your chain nose pliers to lift up one of the inner-most coils.

A good stone for the wire-wrapping technique is wider around the middle than it is at the ends. You can wrap small or large stones, and it's OK if they're slightly irregular in shape. That just makes the jewelry more interesting. This wire-wrapped pendant necklace is a fairly quick and easy project. And it makes for a great personalized gift.

It uses 24g copper wire for the wraps. Select a stone to wrap and cut two pieces of 24 gauge wire about 6 inches long. Note that the exact size will depend on the size of your stone. Cross the wires in the center and twist them together. These wires will align along the side of the stone, so make sure it is at least half the length of the stone.

How to wire wrap stones for beginners, by Bobi Jo Gilman 3 different ways to wire wrap stones | Wire wrapping irregular stones | How to wire wrap stones without holes If you're having trouble figuring out how to wire wrap stones without holes, or wire wrapping irregular stones in general that you may have lying around, have no fear!

In this video I'll show you how you can wire wrap irregular shaped stones and crystals into a beautiful reversible pendant using square and half round wire.E.

Otherwise I wrap large stones in a simple style often used for cabs: 4 wires around the sides of the stone, meeting up top to form the bale. Pull/shape the front and back wire to trap the stone and use leftovers at the top for further decoration. I'll grab a picture when I'm not in mobile. Reply. tropezones •.

Hi Ava, depending on whether your undrilled stones are flat, rounded or very irregular in shape, my best advice would be to first look at the sample photos of these four choices: 1.For a flat stone, similar to a cabochon, you could use DVD 2 in the Beginner Series, that teaches how to formulate and create a frame to make a pendant; 2.

Use appropriate wire thickness. I make jewelry of wire 1 mm (18 ga) wire for the frames and 0.4 mm (26 ga) thick wire for the weaving. You can use wire with a thickness of 0.8 mm (20 ga) wire for the frames and 0.3 mm (28 ga) wire for the weaving. Tension is important when weaving. Too tight and you will pull your frame wires out of shape, but.

Are you interested in learning how to wire-wrap stones without holes? In this wire-wrapping tutorial for beginners, I will show you how to wire-wrap a caboch.

Length = bracelet circumference + 5cm ( 2 inch) and + 10cm ( 4 inch) with wire for wrapping stone In the video I use : 19 gauge ( wire diameter 0.9mm ) : 3 strands, each 20cm ( 8 inch) long and 3.

Read also:

Wire Wrapping Irregular Stones - The pictures related to be able to Wire Wrapping Irregular Stones in the following paragraphs, hopefully they will can be useful and will increase your knowledge. Appreciate you for making the effort to be able to visit our website and even read our articles. Cya ~.