Get All You Need

How To Cut Stair Stringers With A Framing Square


Trim the bottom and top of the stringer. Cut the top of the stringer along the first rise line. Then trim the bottom run line, which was marked so that it is shorter than the others by an amount equal to the thread thickness of your stairs. [13] 5. Use the first finished stringer as a template. Expert carpenter shows you how to measure out, mark and cut a stair stringer. He shows you how it's done with tips thrown in along the way to make this easy.


Selecting stringer stock. Stringers should always be cut from 2x12s. Notching smaller stock doesn't leave enough wood to safely carry the loads of a stair. When ordering stringers, allow about 14 inches of stringer length for each step. Look for straight stock with as few knots as possible. Set the stringer stock on a pair of sawhorses or a work table with the crown facing toward you. Now tighten a stair gauge at 8⅛ in. on one side of the square to represent the unit rise, and tighten the other gauge at 9 in. on the other leg of the square to represent the unit run. Keep the corner of the framing square flat on the stringer.

How to Cut Stair Stringers 15 Steps wikiHow

To mark the notches, measure the thickness of the tread and riser material. This will typically be around 1 inch for each. Starting from the bottom of the stringer, measure up the height of the riser and make a mark. Then, measure the depth of the tread and make another mark. Repeat this process for each step.


A complete discussion and demonstration of how to measure and cut stair stringers for a deck or porch or other use. Watch the whole process, start to finish.


Step III: Make the Cuts. Position one stringer flat on the saw horses. Use your circular saw to slowly and gently cut along the cut line you just made. Remember that because it zig-zags, there will be strong 90-degree angles around which you must cut. I recommend cutting short of the intersections between two lines.


Cutting beyond the notch with the circular saw is faster, but it weakens the stringer. 10. Use the first stringer as a template. To lay out subsequent stringers, align the cut stringer with the edge of the stringer stock, and draw lines. Make the cut, removing the pencil line. Photos: Patricia Steed. More on Stairs:


Mark the first stair notch in the stringer. Orient this notch at least 12 in. from the board's end and clear of any knots. 3. Draw the deck-framing plan onto the stringer face. Clearly mark an X on any waste portions. 4. Align a Speed Square to the adjacent notch line to increase the accuracy of stringer layout. 5.


Use the following stair stringer calculator. Determine the total rise of the staircase. Use a tape measure to record the distance from the upper floor to the lower floor. If the flooring is not yet installed, add the thickness of the flooring to the total rise. Divide the total rise by the estimated height of the stair risers (7- 7 3/4 inches.


After stepping off the lower set, adjust the seat cut as outlined in Part 1. This involves subtracting the 1-inch tread thickness, then adding back 1⅝ inches to account for the fact that the stringers will be installed on the subfloor, which is lower than the finish floor.


Step 4: Cut the Stringers. Once you've traced your template onto your lumber, it's time to cut the stringers. Use a saw to carefully cut along the lines you've traced. Make sure that your cuts are straight and accurate, as any errors can affect the stability and safety of your staircase. If you're using a circular saw, adjust the blade depth so.


Cutting A Stair Stringer. Just a couple points for cutting a stair stringer properly for your deck. Some stairs have notched stringers everywhere. There is no solid stringer covering the outsides of the steps. This deck is an example of that. The treads overhang the stringer on the sides. Aside from making sure you have at least 5" from the.


The stringer will be cut out of a 2"x12" piece of pressure-treated lumber with the appropriate rise and run determined by the finished height of the deck. Stringers are typically placed on either side of the staircase and are angled to support the treads and risers. They are responsible for bearing the weight and forces exerted on the steps.


In this video I show how to calculate, lay out, and cut stair stringers.


The 4 Tips for Cutting Stair Stringers. 1. Take Accurate Measurements. You'll need to have several basic measurements before you can cut your stair stringers. First, the total rise height of the stairs. Then, you'll have to measure the total length of the stairway, which is sometimes called the rise and run.


Preparing the Deck Stair Stringers. Always use straight, high-quality, pressure-treated 2x12s for stringers. Additionally, if you're planning on resting a stringer on the ground, make sure the wood has .60 RET level. You want the crown side of the board to be on the cut side. In order to prepare the stringers, you will want to lay out one of.


Slide the framing square down the stringer edge until the rise line touches the point where the tread line from the previous step intersects the board edge. Make certain the stair gauges rest against the board. Repeat this process to mark all steps. Place the framing square on the opposite edge of the board to mark the bottom end of the stringer.


In this video I am going to show you how to figure the rise and run of the stair stringer.I am also going to show you the easiest and quickest method to cut.


Download Article. 1. Determine the overall height of the stairs. Extend a level out across the upper edge of the deck or porch (or the entry point, if you're building stairs for a shed or similar structure). Stretch your tape measure from the bottom of the board to the ground.


Cut only the top and bottom of the stair stringer with a circular saw. Test-fit the stair stringer by placing it against the deck, and check the tread level with a small level.


HANDY Magazine shows you how to build basic stair stringers.


Cut deck stringers with ease! This How-to video will show you how I go about cutting stringers. I build deck stairs to last for a lifetime! Tools NeededFrami.


The stringer will be cut out of a 2"x12" piece of pressure-treated lumber with the appropriate rise and run determined by the finished height of the deck. Stringers are typically placed on either side of the staircase and are angled to support the treads and risers. They are responsible for bearing the weight and forces exerted on the steps.


Are you curious about the easy way to add a winder to your stair runner? You may improve the appearance and safety of your staircase by correctly binding and.


Gallery of How To Cut Stair Stringers With A Framing Square :

Staircase Stringer Types Cutting Procedure and Code Requirement

How To Cut Stair Stringers 2X10

Inspecting Stair Stringers InterNACHI 174

STAIR STRINGER 3 STEP 7 quot X11 quot PT GROUND CONTACT Pre Cut Stair

How To Cut Stair Stringers With A Framing Square - The pictures related to be able to How To Cut Stair Stringers With A Framing Square in the following paragraphs, hopefully they will can be useful and will increase your knowledge. Appreciate you for making the effort to be able to visit our website and even read our articles. Cya ~.

RSS Feed | Sitemaps
Copyright © 2024 All Rights Reserved.